Lifeboat Foundation

UCLA’s new method to smaller molecule machines.

UCLA nanoscience researchers have determined that a fluid that behaves similarly to water in our day-to-day lives becomes as heavy as honey when trapped in a nanocage of a porous solid, offering new insights into how matter behaves in the nanoscale world.

“We are learning more and more about the properties of matter at the nanoscale so that we can design machines with specific functions,” said senior author Miguel García-Garibay, dean of the UCLA Division of Physical Sciences and professor of chemistry and biochemistry.

Continue reading “UCLA chemists report new insights about properties of matter at the nanoscale” »

We are running out of room and resources here on earth. United Launch Alliance is looking beyond planet earth to solve these problems.

By robots?

Superconducting aluminum or superfluid helium could be used to detect superlight dark matter particles.

Dark matter searches repeatedly draw a blank. One possible reason for the failure may be dark matter’s mass: Despite increased sensitivity, current detectors cannot spot the particles that make up this elusive matter if the particles are extremely light. Now Kathryn Zurek from the Lawrence Berkeley National Laboratory, California, and colleagues have come up with two new ideas for making detectors that should be capable of spotting such superlight particles.

In broad strokes, dark matter detectors are designed to operate as follows: Incoming dark matter particles strike the detector, gently nudging nearby atomic nuclei or electrons in the material from which the detector is made. These rare nudges generate small amounts of energy in the form of light or heat, which the detector registers. But the ability to detect particles of a certain mass depends on the properties of the detector material, such as the mass of its nuclei. Current detectors, made from semiconducting materials or liquid xenon, are sensitive only to particles heavier than about 10 million electronvolts.

I’m amazed no one has done this before, and there’s only one company doing it now. Microfabrica, based in Van Nuys, California, has perfected the technique of mass producing mechanical devices using the same electrodeposition technology used to make computer chips.

“We are the only high-volume production additive manufacturing platform in the market,” Microfabrica CEO Eric Miller tells me. “We use engineering grade metals to make commercially robust parts, and we’re focused on another end of the spectrum from where a lot of the 3D companies are focused, and that’s at the micro scale.”

The resulting devices are vanishingly small, and exquisitely made. How small? The company makes biopsy forceps less than a millimeter in diameter for a medical device company and timing mechanisms (i.e., clocks) that are less than half a centimeter across for a defense contractor, as well many other very small devices and precision parts.

A startup called Proterra has been working on electric buses for years, and its latest model has a pretty impressive range. Its Catalyst E2 Series buses can drive up to 350 miles on a single charge, which means it can go a quite a bit further than Tesla’s top-tier Model S that already boasts a 300-plus-mile range. The vehicle can also outlast its predecessor that can only go for 258 miles. As Wired notes, electric buses might even be better than cars, since they don’t need a huge network of charging stations. They drive a set route, so cities can simply install some where they’re bound to pass — the E2 might not even need to recharge until the end of the day. Further, not everyone can afford an electric vehicle, but most people can afford to ride a bus.

The Catalyst E2 Series buses are powered by two gargantuan batteries the size of mattresses that can store up to 660 kWh. Its lightweight frame, along with its regenerative braking system, also helps it achieve that impressive range. The only thing that might hold cities and companies back from purchasing E2 is that one will set them back $799,000, over twice the amount of a typical diesel bus. Proterra is probably hoping that government subsidies, coupled with the fuel and maintenance savings they’ll get, can convince them to buy the vehicle. If you’re in Los Angeles, you might be able to ride one of the first E2 buses scheduled to hit the road in 2017.

Saya is a computer-generated school girl created by Japanese artists Teruyuki Ishikawa and Yuka Ishikawa. She looks so detailed that she has broken past the uncanny valley, and she could herald a new era in CGI.

Japanese artists Teruyuki Ishikawa & Yuka Ishikawa (a.k.a Telyuka) have given birth to Saya, and she’s remarkable. But despite how realistic she may look, she’s not real. Rather, she’s a computer-generated rendition of a school girl.

Telkuya started the Saya project in 2015, and they have been working to constantly improve her—make her more detailed and more life-like.

Refining and redesigning my Mars rocket.

Love Imgur? Join our team!

“What do Boston, Mass., and Barcelona, Spain have in common with consumer internet platforms like Yelp and Zillow? They’re taking advantage of a growing open-data trend.”

Read more